Filippo,
Thanks for the comments, I had to go back to my first post to check to make sure I put in wet clutch
Paul
| Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum http://ducatittandf1.com/ |
|
| Pantah project http://ducatittandf1.com/viewtopic.php?f=27&t=12208 |
Page 4 of 5 |
| Author: | 583 [ Tue Jan 02, 2024 2:52 pm ] |
| Post subject: | Re: Pantah project |
Hi Huit happy new year to you Very good looking engine, in looking at your previous post you mentioned a dry clutch but now i don't know when you switch on wet clutch. I'm curious to see the look of the fairing once everiyhing is in place. Enjoy your project Filippo |
|
| Author: | huit [ Tue Jan 02, 2024 8:41 pm ] |
| Post subject: | Re: Pantah project |
Filippo, Thanks for the comments, I had to go back to my first post to check to make sure I put in wet clutch Paul |
|
| Author: | 583 [ Thu Jan 04, 2024 8:27 am ] |
| Post subject: | Re: Pantah project |
Hi Paul It's my fault on your first post you report about a wet clutch Apologies Filippo |
|
| Author: | huit [ Thu Jan 04, 2024 8:03 pm ] |
| Post subject: | Re: Pantah project |
No apology needed! How’s your Tt coming along? |
|
| Author: | 583 [ Fri Jan 05, 2024 7:44 am ] |
| Post subject: | Re: Pantah project |
Quote: huit wrote: No apology needed! How’s your Tt coming along? Hi Paul still from my side because i'm working abroad. I know the guys are proceeding with Head holder to machine valves seat.i will update as soon i receive pics. Regards Filippo |
|
| Author: | huit [ Sat Jan 06, 2024 3:04 pm ] | ||
| Post subject: | Re: Pantah project | ||
Did a test fit after shock was tacked in place, close but no cigar  I need to move the left tab at the top over about 6mm Mounted the the right side exit exhaust so I can start to make the rest of the exhaust
|
|||
| Author: | 618F1 [ Sat Jan 06, 2024 8:36 pm ] |
| Post subject: | Re: Pantah project |
And i am waiting to see how the camshaft pulleys are aligned! MikeV HNY Paul. Ooh. I like that muffler. |
|
| Author: | huit [ Sun Jan 07, 2024 9:46 am ] |
| Post subject: | Re: Pantah project |
Mike, I haven’t done the cam timing yet, I set the timing mark on the vertical pulley to its normal position then rotated the cam to correct position and put in 3 cap screws, tightened the screws put in the rest of the screws installed the belts and rolled over the motor, no collisions! I had to remove a little material off the top of the pistons, the plugs were too close for comfort. That muffler makes the bike!
|
|
| Author: | huit [ Fri Feb 23, 2024 8:47 pm ] | ||
| Post subject: | Re: Pantah project | ||
Going to the painters tomorrow!
|
|||
| Author: | 618F1 [ Fri Feb 23, 2024 9:08 pm ] |
| Post subject: | Re: Pantah project |
I don’t see how they can improve on that! No headlight - a track bike? MikeV |
|
| Page 4 of 5 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|