DUCATI TT and F1 FORUM
 
It is currently Sat Nov 18, 2017 2:23 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 26 posts ]  Go to page Previous  1, 2, 3
Author Message
 Post subject: Re: Cranckshaft bearing
PostPosted: Sun Aug 13, 2017 4:56 pm 
Offline

Joined: Wed Aug 27, 2014 3:36 pm
Posts: 80
Hi Ducadini thanks for replying.
This discussion is open,i was just wondering if there is an alternative to the stock crankshaft bearing, this is why i named 6307/6207, but if i understand these bearings did not comply with the stock specs.
Ciao
Filippo


Top
 Profile  
 
 Post subject: Re: Cranckshaft bearing
PostPosted: Wed Aug 16, 2017 9:53 pm 
Offline

Joined: Thu Oct 14, 2010 7:30 am
Posts: 139
Filippo, Loctite make a compound specific for mounting bearings. I think it is green in color and called Stud and Bearing mount. In a pinch I've used the high strength Red 271 [I think] with decent results when the fit in the case wasn't too loose. Yes those pics do show angular contact type bearings.


Top
 Profile  
 
 Post subject: Re: Cranckshaft bearing
PostPosted: Sat Aug 19, 2017 5:03 pm 
Offline

Joined: Sat Feb 25, 2017 11:51 am
Posts: 166
I have one nos main bearing and main seal in my stash of xtra parts. But need someone to confirm this is good spec for you to use. PICTURES ATTACHED. Made in usa bearing, New Departure #Q20307DTL (I think 15 deg angular contact?)
Seal is Corteco 75-95-12. If you can use $30?

Clay


Attachments:
20170819_135204.jpg
20170819_135204.jpg [ 750.52 KiB | Viewed 224 times ]
20170819_134717.jpg
20170819_134717.jpg [ 865.34 KiB | Viewed 224 times ]
Top
 Profile  
 
 Post subject: Re: Cranckshaft bearing
PostPosted: Tue Aug 22, 2017 9:02 am 
Offline

Joined: Wed Aug 27, 2014 3:36 pm
Posts: 80
Hi Wdietz186 and thanks for Info about Loctite.

Hi Cal , the bearing shown in your photo look wery close to the ones i dismounted.
75-95-12 could this code be referred to inch instead centimetres?
Ciao
Filippo


Top
 Profile  
 
 Post subject: Re: Cranckshaft bearing
PostPosted: Tue Aug 22, 2017 12:55 pm 
Offline

Joined: Sat Feb 25, 2017 11:51 am
Posts: 166
583 wrote:
Hi Wdietz186 and thanks for Info about Loctite.

Hi Cal , the bearing shown in your photo look wery close to the ones i dismounted.
75-95-12 could this code be referred to inch instead centimetres?
Ciao
Filippo


Hi,
The dashed #'s are for the seal. I think that must be used on a dry clutch pantah, I bet your 350 is not dry?


Top
 Profile  
 
 Post subject: Re: Cranckshaft bearing
PostPosted: Sun Sep 24, 2017 1:53 am 
Offline

Joined: Wed Aug 27, 2014 3:36 pm
Posts: 80
Hi everybody
So, after a same searches I went to my local Ducati store and ask for crankshaft bearings.
For Pantah and Alazzurra engines, Ducati supply the same bearings used in 90'/00' models.
There is difference between the new one and the old ones, but at the end I buy these , on the following link you find the new ones and the old ones.
https://www.flickr.com/photos/156916018 ... res/6hGEvx

Ciao
Filippo


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 26 posts ]  Go to page Previous  1, 2, 3

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Template made by DEVPPL