|
View unanswered posts | View active topics
Author |
Message |
583
|
Post subject: Re: my Pantah racer Posted: Sun Jun 26, 2016 11:48 am |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 334
|
So I was in Adria too, I meet Carlo and see his beautiful, and fast bike. With the new 36 dell'orto carbs I gain 1000 revs and now I can reach 9500 r easily. I can also take the engine at 10.000 but I prefer to remain on a safety range. L87yc Champion sparks and needle at the lower setup. I gain in speed and acceleration, and I feel very good with the bike I just finished the race in 8th position on 13, but with the 4th at just 1 second far. Ciao Filippo
Last edited by 583 on Tue Jul 25, 2017 6:26 am, edited 1 time in total.
|
|
Top |
|
|
eric
|
Post subject: Re: my Pantah racer Posted: Mon Jun 27, 2016 1:33 am |
|
Joined: Wed Nov 03, 2010 3:51 pm Posts: 10
|
top, bravo
|
|
Top |
|
|
583
|
Post subject: Re: my Pantah racer Posted: Mon Jun 27, 2016 2:24 am |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 334
|
Hi Eric, thank you very much. Ciao Filippo
|
|
Top |
|
|
pantah_good
|
Post subject: Re: my Pantah racer Posted: Mon Jun 27, 2016 10:51 am |
|
Joined: Fri Oct 15, 2010 12:20 pm Posts: 1275 Location: Vermont, USA
|
|
Top |
|
|
583
|
Post subject: Re: my Pantah racer Posted: Tue Jun 28, 2016 5:18 am |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 334
|
Thank you Pantah_good!! Ciao Filippo
|
|
Top |
|
|
flattop900
|
Post subject: Re: my Pantah racer Posted: Tue Jun 28, 2016 9:34 am |
|
Joined: Tue Mar 18, 2014 10:03 am Posts: 368
|
Hi Filippo... Eighth is two places closer to the podium. Nice job. I don't recall you mentioning the capacity of your motor, just something about 350 heads? Keep up the good fight... Flattop900
|
|
Top |
|
|
583
|
Post subject: Re: my Pantah racer Posted: Tue Jun 28, 2016 10:46 am |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 334
|
Hi Flattop900 thanks for repliyng. you are Right, i have 350 standard head and engine block, plus 540 cc (82mm bore) kit. ciao Filippo
|
|
Top |
|
|
ducadini
|
Post subject: Re: my Pantah racer Posted: Wed Jun 29, 2016 9:32 am |
|
Joined: Wed Sep 11, 2013 7:13 am Posts: 268
|
|
Top |
|
|
583
|
Post subject: Re: my Pantah racer Posted: Sun Jul 10, 2016 5:50 am |
|
Joined: Wed Aug 27, 2014 3:36 pm Posts: 334
|
Hi Ducadini and thanks for the link. The season is on the summer stop, so is time for same jobs. I get an Elefant oil cooler and now trying to fit it on the fairing of my bike. i just set the line from the oil pump to the cooler, need to do the return line from the cooler to the block: without drilling or milling any parts could be an alternative to use the oil filler hole on the right carter to enter in? of course in this case i need a dedicated cap. this have any sense? ciao Filippo
|
|
Top |
|
|
618F1
|
Post subject: Re: my Pantah racer Posted: Sun Jul 10, 2016 11:36 am |
|
Joined: Thu Oct 14, 2010 11:23 am Posts: 1826
|
Hello Filippo. Please show us where the line comes out of the engine (clutch cover?) first. You need to be careful about where you put the line back in, but I do not think the filler is good, and I have never seen that done. The better way is to put it back into the end of the crank since you may have taken some from it at the oil pump. That will require tapping into the cover (again?). And, the passage inside the cover from the pump to the crank should be blocked or there will be some confusion/conflict about which way the oil is flowing. I will stop here, because I am sure others have even more knowledge than me. There are many ways to do this, but some are probably wrong! I recently saw a photo posted here of a partial bike for sale, and the routing of the oil lines was "puzzling", even troublesome to me. But not knowing what was done inside it might have been OK. Sorry, I did not stop, kept pecking away here. Now more: You did not mention separate lines to the cam end caps. That is another "can of worms", but will certainly require disassembling the top of the engine. Wait till winter if you are doing that. Go racing. I remembered that Pat Slinn said Shell Oil told him the oil temperature on the 1981 Isle of Man-winning F2 Pantah (#8) was fine, and they did not need a cooler! MikeV PS: those to avoid; one is like Cirque du Soleil, and one is uncertain. Attachment:
oil lines a.JPG [ 40.84 KiB | Viewed 146228 times ]
Attachment:
oil lines 3.jpg [ 202.06 KiB | Viewed 146228 times ]
|
|
Top |
|
|
Who is online |
Users browsing this forum: No registered users and 13 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|
|