Hi!
I need to replicate the fixings of the seat (the removable part) of the F1 and I would need a clear image of those pieces.
I would appreciate your help
Regards
| Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum http://ducatittandf1.com/ |
|
| Ducati 750 F1 Seat. http://ducatittandf1.com/viewtopic.php?f=24&t=11864 |
Page 1 of 1 |
| Author: | 750TT [ Sun Dec 23, 2018 9:34 am ] |
| Post subject: | Ducati 750 F1 Seat. |
Hi! I need to replicate the fixings of the seat (the removable part) of the F1 and I would need a clear image of those pieces. I would appreciate your help Regards |
|
| Author: | Beas42 [ Sun Dec 23, 2018 2:20 pm ] | ||
| Post subject: | Re: Ducati 750 F1 Seat. | ||
The special screw shown is used in 3 places circled in red
|
|||
| Author: | 750TT [ Sun Dec 23, 2018 5:14 pm ] |
| Post subject: | Re: Ducati 750 F1 Seat. |
not those parts, those that go in the part 25 |
|
| Author: | wdietz186 [ Mon Dec 24, 2018 7:44 pm ] |
| Post subject: | Re: Ducati 750 F1 Seat. |
Pretty sure the base is just an 'L' shaped piece of plastic or thick cardboard about 6mm thick and is 19mm or so smaller than the edges of the seat cowling edges. Probably not too difficult to replicate as it isn't curved/arced underneath because the seat cowling is flat in the seting area. The hard parts would be the special bolts and spring clips that hold it in. I'd use Velcro. |
|
| Author: | 750TT [ Tue Dec 25, 2018 5:47 am ] |
| Post subject: | Re: Ducati 750 F1 Seat. |
wdietz186 wrote: Pretty sure the base is just an 'L' shaped piece of plastic or thick cardboard about 6mm thick and is 19mm or so smaller than the edges of the seat cowling edges. Probably not too difficult to replicate as it isn't curved/arced underneath because the seat cowling is flat in the seting area. The hard parts would be the special bolts and spring clips that hold it in. I'd use Velcro. Same did not explain me well  , I would like to know how are the metal parts that go in the saddle that is extracted and that fit in the part number 20.
|
|
| Author: | wdietz186 [ Tue Dec 25, 2018 4:16 pm ] |
| Post subject: | Re: Ducati 750 F1 Seat. |
As I recall the seat base has a metal spring clip with parallel wires approx. 6mm apart that spread over and clip around the "special" bolts on the cowling. I think the clip is just pop riveted onto the seat base. They are attached over holes drilled in the seat base. So the wires spread over the conical part of the bolt and clip into the reduced diameter at the base of it. Pretty clever actually. |
|
| Author: | 750TT [ Tue Dec 25, 2018 7:05 pm ] |
| Post subject: | Re: Ducati 750 F1 Seat. |
is what I want to see, 
|
|
| Author: | MarcFX [ Tue May 12, 2020 12:11 am ] | ||
| Post subject: | Re: Ducati 750 F1 Seat. | ||
I haven't got the wire clips, but this is the pin
|
|||
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|