A few more beers and it should be done!!!
| Attachments: |
|
100_2221.JPG [ 1.04 MiB | Viewed 7743 times ] |
|
100_2222.JPG [ 1023.92 KiB | Viewed 7743 times ] |
| Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum http://ducatittandf1.com/ |
|
| TT1 Ducati replica http://ducatittandf1.com/viewtopic.php?f=12&t=1334 |
Page 1 of 5 |
| Author: | boucher [ Sun Dec 04, 2011 1:57 am ] | |||
| Post subject: | TT1 Ducati replica | |||
A few more beers and it should be done!!!
|
||||
| Author: | Belt Boy [ Sun Dec 04, 2011 3:36 am ] |
| Post subject: | Re: TT1 Ducati replica |
A chain will help it go more than beer..... Beautiful bike! |
|
| Author: | nojapanbike [ Sun Dec 04, 2011 3:45 am ] |
| Post subject: | Re: TT1 Ducati replica |
 great!!!! |
|
| Author: | pantah_good [ Sun Dec 04, 2011 10:48 am ] |
| Post subject: | Re: TT1 Ducati replica |
Normally I (tongue in cheek) pooh-pooh street TT's, but I have to admit I really like this bike. A lot of very nicely done work sitting there, you must be very proud of it. Hope you live near a bunch of curvy roads. Nice job! Bill |
|
| Author: | graeme [ Sun Dec 04, 2011 8:46 pm ] |
| Post subject: | Re: TT1 Ducati replica |
Looking good Chris, Got any pictures of your side stand without the pipe? Black top Dellorto's,,,, watch out the float isn't tight in the mounting pins and sticks down, flooding the lower fairing like mine did. Graeme |
|
| Author: | boucher [ Mon Dec 12, 2011 5:11 am ] | ||||
| Post subject: | Re: TT1 Ducati replica | ||||
Graeme , i used cagiva 650 stand , made a 3mm plate that picked up the 2 holes plus i helicoiled last hole for strength on Lower engine mount lug that not used on verlicchi frame. welded stand to plate bolted through stand/plate to cases. used counter sunk allen bolt on one closest to pipe. Then heated and bent stand to suit pipe.
|
|||||
| Author: | boucher [ Thu Mar 26, 2015 2:51 am ] | |||
| Post subject: | Re: TT1 Ducati replica | |||
It's been a while since i've played with the TT1, it was going to be registered on the road. But the psycho pantah put a end to that. So it's going to be a club track bike. I,m making a few changes and finally going to finish it. Boucher.
|
||||
| Author: | ducalf [ Fri Mar 27, 2015 3:08 pm ] |
| Post subject: | Re: TT1 Ducati replica |
Great job, it looks very good! |
|
| Author: | huit [ Fri Mar 27, 2015 7:14 pm ] |
| Post subject: | Re: TT1 Ducati replica |
Beeeutiful!!! Paul |
|
| Author: | ducttf1 [ Fri Mar 27, 2015 9:31 pm ] |
| Post subject: | Re: TT1 Ducati replica |
Great job Boucher! Lou |
|
| Page 1 of 5 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|