Klasse Wolf!
I am one of many wanting to fit fine-spline gearbox parts into his Pantah cases!!!
Now - with help from the site PantahIG - we can do it hopefully without tears
Poison
| Ducati TT1, Ducati TT2 and Ducati 750 F1 Forum http://ducatittandf1.com/ |
|
| coarse spline to fine what do I need to do? http://ducatittandf1.com/viewtopic.php?f=10&t=10126 |
Page 1 of 1 |
| Author: | huit [ Wed Dec 26, 2012 7:31 pm ] |
| Post subject: | coarse spline to fine what do I need to do? |
I have a fine spline transmission from a paso, what do I need to do the install into a set of allazurra cases? Having a real hard time with output shaft shimming! Thanks Paul |
|
| Author: | TT1-F1 [ Thu Dec 27, 2012 3:32 am ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
Is the schaft too wide, too narrow or are the gears out of line? Did you use all the paso parts? Jarno |
|
| Author: | huit [ Thu Dec 27, 2012 8:57 am ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
Thanks Jarno, I am using all the paso parts, the problem is the gear closest to the clutch hits the webbing in the cases, or the retainer that locks the bearing in place. With the first and last gear removed I can shimm the shaft. Paul |
|
| Author: | TT1-F1 [ Thu Dec 27, 2012 5:17 pm ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
Hmmm, I will check a pantah case with a Paso shaft when I get into the shop one of these days. Or maybe somebody else knows what can be done. I remember that I had some tight space on the clutch shaft too, but that was with paso cases with 750SS shafts Jarno |
|
| Author: | Wolf [ Sun Dec 30, 2012 4:53 am ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
Hi Paul, the Allazzura and Pantah cases are identical, as far as I know. Have a look here: http://pantah-ig.de/index2.html then go to: Technikseite and then to: Getriebeumbau text is in German, but there are some pictures showing the necessity to remove some material of the cases. In the described conversion, the internals of a Monster were used. Regards Wolf |
|
| Author: | huit [ Sun Dec 30, 2012 11:04 am ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
Thanks Wolf! Those pictures describe what i found, I will translate it and work through it. Thanks Again!!! Regards Paul |
|
| Author: | TT1-F1 [ Sun Dec 30, 2012 5:05 pm ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
There is the answer ! Nice site Jarno |
|
| Author: | Poison [ Tue Jan 01, 2013 2:19 am ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
Klasse Wolf! I am one of many wanting to fit fine-spline gearbox parts into his Pantah cases!!! Now - with help from the site PantahIG - we can do it hopefully without tears Poison |
|
| Author: | athleticroman [ Tue Jan 01, 2013 7:59 am ] |
| Post subject: | Re: coarse spline to fine what do I need to do? |
Here is the English translation of the website below: http://translate.google.com.au/translat ... CDgQ7gEwAA |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|